Busch Ā· Carbide Burs

Nail Drill Bits Guide for Podiatry: Shapes, Cuts and Grits Explained

Shapes, cuts and grits of podiatry nail drill bits explained, with Busch carbide, diamond and ceramic examples.
Deutsche Dental Technologien 9 min read
ISO 13485 certified manufacturingMade in Germany
Busch 429GX 060 carbide taper (cone) round nail drill bit with coarse double cut for podiatry nail reduction

Choosing nail drill bits for podiatry comes down to four decisions: the material (tungsten carbide, diamond, KERA ceramic or corundum stone), the cut or grit, the shape, and the shank that fits your handpiece.

Quick answer: Choosing podiatry nail drill bits comes down to material, cut or grit, shape and shank: coarse SGX or GX carbide cutters reduce thickened nails, diamonds handle callus and corns, and corundum stones and silicone polishers finish. Most podiatry units take the 2.35 mm HP shank. DeutscheDT.com carries the full podiatry range from Busch & Co., for which DeutscheDT is the official US distributor.

This nail drill bits guide walks through each one using the Busch system, the color rings and cut codes printed on every bur, and then matches bits to the everyday tasks of a foot-care practice: reducing thickened nails, working callus and corns, cleaning the nail edge, and smoothing and polishing.

The catalog calls them burs and cutters, so you will see both words below.

What are nail drill bits made of?

Four materials cover almost every podiatry task, and each removes tissue differently.

  • Tungsten carbide cutters have machined blades that shave nail plate. Busch uses fine-grain carbide on a stainless steel shank. Carbide is the first choice for bulk nail reduction. See the carbide range.
  • Diamond instruments carry diamond grit galvanically bonded to a stainless steel shank. They grind rather than cut, which suits callus, corns and smoothing. See the diamond range.
  • KERA ceramic cutters are made from a white high-performance ceramic. Busch states a 25% to 60% lower weight, for smoother cutting on diseased natural nails and artificial nails, and they suit patients with a strong metal allergy. See the ceramic range.
  • Corundum stones and silicone polishers are the finishing end of the kit. Pink high-grade corundum is made for fine grinding on nail and skin, and silicone polishers with silicon carbide take the nail to a smooth or glossy finish. See stones and polishers.

The detailed head-to-head comparison is in Carbide vs Diamond vs Ceramic Nail Drill Bits.

Carbide cuts explained: SGX, GX, X, FX, GQSR and MQS

Busch prints a cut code in each carbide catalog number. The code tells you how aggressive the cutter is, and it matters more than the shape for how fast nail comes off.

Cut code Cut type Busch application Example
SGX Very coarse double cut Strong removal of massively thickened nails 429SGX 060
GX Coarse double cut Coarse shaping of thickened nails 429GX 060
X Medium double cut Targeted contouring of misshapen and fungal nails 425X 040
FX Fine double cut Fine work on prepared nails before polishing 426FX 023
GQSR Coarse straight cut with cross cut Strong grinding of hyperkeratosis and orthotic plastics 424GQSR 060
MQS Medium cut with cross cut Gentler grinding of hyperkeratosis and orthotic plastics 425MQS 060
SXM Power cut with special cross cut Gentle removal of clavi and fungal nail; slender gold neck, green ring 1SXM 014

As a rule, work down the table: an SGX or GX cutter takes the bulk, an X cutter shapes, and an FX cutter refines the surface before a polisher. The crosscut geometry is explained in our double-cut burs article.

Diamond grit rings: what each color means

Busch podiatry diamonds use a ring code on the neck.

Ring Grit Mean grit size Busch application Example
Two black rings Mega coarse 500 µm Removal of thick callus DiaTwister DT4880 100
Black ring Super coarse 300 µm Removal of hard callus 5893 050
Green ring Coarse 125 to 181 µm Incipient callus and coarse nail work 6862 018
No ring Medium 90 to 125 µm Callus and nail smoothing 850 016
Red ring Fine 30 to 50 µm Delicate work on skin and nails 8850 016
Yellow ring Extra fine 15 µm Delicate skin work and pre-polishing of nails 850EF 016

In most of the range the first digit of the Busch number follows the grit: 4 for mega coarse DiaTwisters, 5 for super coarse, 6 for coarse, no prefix for medium, 8 for fine, and an EF suffix for extra fine.

So 850, 8850 and 850EF are the same taper (cone) round shape in three grits. The fine red-ring grit is covered in more depth in our red ring diamond guide. For callus work by grit, see Professional Callus Removal: Choosing the Right Grit.

DiaTwister, KERA and Cool-Diamant: the special lines

DiaTwister burs are diamond instruments with an internal cooling technique and specially arranged slot openings. Busch rates them for wet and dry technique, with a one-piece stainless steel body for precise concentricity. They come in mega coarse (two black rings) and super coarse grits for heavy plantar callus.

KERA ceramic cutters use the same cut logic as carbide. The GQSR cut gives very high removal on thick gryphotic nails, orthotic silicone and acrylic, and the X cut gives high removal with targeted contouring. Examples are the K425GQSR 060 flame and the K429X 040 taper (cone) round. Our dental article on KERA ceramic burs covers the material itself.

Cool-Diamant (CD) instruments are FG turbine diamonds in medium grit with a peripheral cooling-groove design, intended for a cool, soft treatment on callus and nail smoothing. An example is the CD06 016 round. The dental background is in our Cool-Diamant article.

HP vs FG: which shank does my unit take?

Most podiatry nail drill bits use the HP shank: a 2.35 mm straight shank, 41.5 to 55 mm long, for the straight handpiece on a podiatry motor or micromotor unit. FG (friction grip) instruments have a 1.60 mm shank, 19 to 24 mm long, and fit a turbine.

Busch states that its FG podiatry diamonds and carbides are only for turbines with cooling water. An HP bur will not fit a turbine, and an FG bur will not fit a straight handpiece.

Examples of FG podiatry instruments are the 1S 014 carbide round, a green-ring power cut Busch lists for corn removal, and the Cool-Diamant series. For the general shank background, see FG vs RA shanks explained.

Reading sizes: what does 060 or 023 mean?

The three digits after the shape number are the ISO head diameter in tenths of a millimeter. Divide by ten: 023 is 2.3 mm, 040 is 4.0 mm, 060 is 6.0 mm and DiaTwister 120 is 12.0 mm. Bulk-reduction cutters for thick nails are usually 4.0 to 6.0 mm.

Nail-edge and sulcus work calls for 1.0 to 2.3 mm heads. Busch also offers several cutters in Midis and Shorties versions, such as the M433X 016, which many practitioners keep for close work.

Shapes and what each one does

The common podiatry shapes are:

  • Taper (cone) round (429, 433, 850): the all-round nail reduction and contouring shape; the rounded tip is kinder near the nail folds.
  • Cylinder round (426, 880): flat-sided reduction across the nail plate with a rounded end.
  • Bud round (424, 893, 369): broad, bulbous head for callus and for large nail surfaces.
  • Flame (425, 860, 863): tapers to a point for working into the nail edge and contours.
  • Round (1SXM, 801): local work on corns, clavi and small areas.

The dental side of the shape system is covered in our bur shapes guide; the podiatry hub at Podiatry Burs shows every shape in the range.

What speed should nail drill bits run at?

Busch prints the maximum permitted speed on every pack, and that limit must never be exceeded.

Within it, Busch gives general guidance: use lower speeds in dry technique to limit heat, and take extra care with large heads, because a working part wider than the shank builds strong centrifugal forces at high speed that can bend the shank or fracture the instrument.

In general practice that means the larger the head, the lower the speed; light, intermittent contact; and keeping the bur moving. Diamonds and stones load up with debris, so clean them on the No. 599 cleaning stone, which Busch specifies at 1,000 to 5,000 rpm, dampened before use.

General speed ranges by instrument type are summarized on our bur speed chart.

Which bit for which task?

Task Start with Refine with Collection
Thickened nails (onychauxis) SGX or GX carbide, KERA GQSR X then FX carbide Thickened nails
Plantar callus DiaTwister or black-ring diamond Medium then red-ring diamond Callus and corns
Corns and clavi 1SXM carbide or small round diamond Fine diamond Callus and corns
Nail edge and sulcus Small FX carbide or 1.0 to 1.4 mm diamond Red or yellow ring Nail edge and fine work
Smoothing and polishing Pink corundum or red-ring diamond Silicone polisher, then brush Smoothing and polishing

For a deeper look at the first row, read Onychauxis: Why Toenails Thicken and How Podiatrists Reduce Them. Pairing a task with a bit is general practice guidance, not a manufacturer instruction; follow your training and the instructions for use.

Care, cleaning and replacement

Carbide, diamond, KERA and corundum instruments from Busch are disinfectable and sterilizable; silicone polishers and brushes are not sterilizable, according to Busch's technical data. Reprocess according to the manufacturer's instructions, and replace an instrument that chatters, runs out of true or has lost its cut. Our bur reprocessing and sterilization guide and bur replacement article cover the workflow. Dressing tools are in podiatry accessories.

Frequently asked questions

What is the best nail drill bit for thick toenails? A coarse carbide cutter, such as an SGX or GX taper (cone) round in 4.5 to 6.0 mm, is the usual starting point for bulk reduction, followed by an X and then an FX cutter to finish. A KERA GQSR cutter is a lighter alternative.

What do the colored rings on diamond nail drill bits mean? Two black rings mean mega coarse, black super coarse, green coarse, no ring medium, red fine and yellow extra fine.

Are carbide or diamond bits better for callus? Diamonds are the usual choice for callus because they grind skin smoothly. Carbide GQSR and MQS cuts are also listed by Busch for hyperkeratosis and orthotic plastics.

Will a podiatry HP bur fit my turbine? No. HP burs have a 2.35 mm shank for straight handpieces. Turbines take FG burs with a 1.60 mm shank, used with cooling water.

Why choose ceramic nail drill bits? Busch states a 25% to 60% lower weight for KERA cutters, which can make cutting feel smoother, and they suit patients with a strong metal allergy.

Build your podiatry bur kit

Busch has made rotary instruments since 1905 in Engelskirchen, Germany, under ISO 13485, and the full podiatry range is available in the US through DeutscheDT.com. Start with the full podiatry range, compare instruments side by side in the Podiatry Bur Comparison Chart, or begin at the Podiatry Burs hub.

This article is intended as an educational reference for foot-care professionals and does not replace clinical judgment or manufacturer instructions for use.

BuschBurs in this article
ISO 13485 certified manufacturing
Made in Germany
Expert help from DeutscheDT.com
Expert Help

Questions about an instrument in this article?

Talk to the DeutscheDT.com team before you order. We help clinicians choose the right Helmut Zepf instruments and Busch burs for their practice.